About Mangal Electrical Industries Pvt Ltd - Electric Components Supplier in India

Based in Jaipur, Rajasthan, India, Mangal Electrical Industries Pvt Ltd lists six active products in its catalogue. The company’s offerings fall under electric components and steel coils, specifically core coil assembly, slit coils, toroidal cores, wound core, immersed circuit breaker (ICB) and amorphous core. The slit coils are classified under HS code 7226.11 and are made from cold rolled grain oriented (CRGO) silicon steel with silicon content between 2.8 % and 3.5 %. The immersed circuit breaker carries HS code 8535.30 and uses copper‑silver alloy contacts, epoxy resin insulators and either SF6 gas or mineral oil as dielectric medium. These entries reflect the supplier’s focus on magnetic and protection components for power equipment.

Product Range and Specialties of Mangal Electrical Industries Pvt Ltd

Slit coils in the HS 7226.11 band are usually supplied as grain‑oriented electrical steel sheets with thicknesses from 0.2 mm to 0.5 mm and magnetic permeability above 5 000 % at 50 Hz. Buyers often request IEC 60404‑3 compliance and material test certificates confirming silicon content and tensile strength. Toroidal cores and wound cores are commonly produced in diameters ranging from 25 mm to 300 mm, with winding grades such as Class A or Class B enamel wire and insulation class V. Immersed circuit breakers classified under HS 8535.30 are typically rated from 5 kA to 65 kA, conform to IEC 60947‑2, and are tested for dielectric strength, contact resistance and breaking capacity. Amorphous cores are made from Fe‑based amorphous alloys offering lower core loss than conventional silicon steel, and are often supplied with loss figures at 50 Hz below 0.5 W/kg. The catalogue therefore covers a spectrum from raw magnetic steel to finished protection equipment.

Trade and Export Information - Mangal Electrical Industries Pvt Ltd

India is a major exporter of electrical steel, magnetic cores and low‑voltage circuit breakers, with key markets in Southeast Asia, the Middle East, Africa and Europe. HS 7226.11 products are subject to customs inspections for material composition and are frequently accompanied by a Certificate of Origin and a test report complying with BIS IS 2060 or IEC 60404‑3. For HS 8535.30 breakers, importers commonly require IEC 60947‑2 test certificates, RoHS declarations and, where applicable, a CE mark for EU shipments. Shipping is typically arranged in 20‑ft or 40‑ft containers with cores packed in wooden crates and breakers in anti‑static cartons. Common Incoterms used by Indian exporters include FOB Jaipur port or CIF destination, with freight forwarding firms handling customs clearance in the buyer’s country.

Sourcing from Mangal Electrical Industries Pvt Ltd - Buyer Guidance

Buyers should request material test certificates that detail silicon percentage, magnetic permeability and tensile strength for the slit coils, as well as loss measurements for the amorphous core. For the immersed circuit breaker, a full IEC 60947‑2 test report, dielectric voltage test results and a declaration of the dielectric medium (SF6 or mineral oil) are standard verification documents. Sample orders of 10‑20 units per product type are typical before scaling to full container loads, and lead times of 4 to 6 weeks are reported for assembled cores and breakers. Verify that packaging meets IS 14744 standards for mechanical protection and that moisture content is below 0.1 % for steel products. Confirm that the supplier can provide CE marking documentation if the shipment is destined for the European Union.

What electric component categories does Mangal Electrical Industries offer?

The catalogue lists six items: core coil assembly, slit coils (HS 7226.11), toroidal cores, wound core, immersed circuit breaker (ICB, HS 8535.30) and amorphous core, all falling under electric components and steel coils.

Are material specifications available for the slit coils?

Yes, the slit coils are made from cold‑rolled grain‑oriented silicon steel with Si content 2.8‑3.5 % and are classified under HS 7226.11; buyers can request a material test certificate confirming composition and magnetic properties.

Which standards apply to the immersed circuit breaker?

The ICB complies with IEC 60947‑2 for low‑voltage circuit breakers and is typically tested for breaking capacity, dielectric strength and contact resistance; certification documents should be provided on request.

What are typical packaging and shipping methods for the cores?

Magnetic cores are usually packed in wooden crates with moisture‑proof liners, while breakers are placed in anti‑static cartons; shipments are sent in standard 20‑ft or 40‑ft containers under FOB or CIF terms.

What certifications should a buyer request from this supplier?

Buyers should ask for material test certificates, IEC compliance reports, RoHS declarations and, for EU destinations, a CE marking declaration; the supplier’s internal tiers do not substitute for these industry certifications.

What is the usual minimum order quantity and lead time?

Sample quantities of 10‑20 pieces per product are common, with full production lead times ranging from four to six weeks after order confirmation.

Which markets commonly import these Indian electrical components?

Major import regions include Southeast Asia, the Middle East, Africa and Europe, where utilities, equipment manufacturers and industrial installers source magnetic steel and low‑voltage breakers.