About National Material Supply Co., LLC - Skin Gel Supplier in United States

National Material Supply Co., LLC is based in the United States and currently lists five active products in its catalogue. The company is classified as an imported supplier with a harbor trust tier, indicating a moderate level of verification. Its product set includes an 8 oz. Tend Skin gel, an "Aluminum" & fragrance‑free deodorant stick, a nail hardener, a moisturizing body lotion, and a 16 oz. Air Shave gel. Each item falls under the broader cosmetics umbrella, specifically skin care, personal deodorant, nail care and shaving categories. The catalogue does not provide HS codes, so the items are generally classified under HS chapter 33 for cosmetics and personal care preparations.

The five products represent typical consumer‑oriented formulations that are shipped in small retail containers such as 8 oz bottles, 16 oz tubes and stick formats. Skin gels like Tend Skin are water‑based, clear gels used for topical treatment, while the Air Shave gel is a silicone‑based lubricant for wet shaving. The deodorant stick is marketed as aluminum‑free and fragrance‑free, addressing a niche for hypoallergenic personal care. The nail hardener is a polymer‑based solution intended to strengthen keratin, and the body lotion is an oil‑in‑water emulsion for moisturisation. All products are listed under the supplier’s top categories of Skin Gel, Cosmetics Products, Nail Polish and Body Lotion.

Product Range and Specialties of National Material Supply Co., LLC

The catalogue lists a skin‑care gel (8 oz Tend Skin), an aluminum‑free deodorant stick, a nail hardener, a moisturizing body lotion and a 16 oz Air Shave gel. In the cosmetics industry, skin gels are usually formulated with a viscosity of 10‑30 cP, a pH between 5.0 and 7.0, and contain preservatives such as phenoxyethanol to meet microbial limits of <10 CFU/g. Deodorant sticks marketed as "fragrance‑free" typically use antiperspirant‑free actives like baking soda or magnesium hydroxide and must comply with the US FDA’s OTC monograph for topical antiperspirants. Nail hardeners commonly contain nitrocellulose or acrylate polymers, with a hardness rating measured by a Shore D scale of 55‑65. Body lotions are oil‑in‑water emulsions with a typical viscosity of 200‑500 cP, containing 3‑5 % emollients and a preservative system that meets ISO 11930 microbial criteria. Air shave gels are often silicone‑based (e.g., dimethicone) with a cloud point above 40 °C and a foam stability measured by a foam height of at least 30 mm after 5 minutes.

Trade and Export Information - National Material Supply Co., LLC

United States exporters of cosmetics and personal care products usually classify their goods under HS 3304 (beauty or make‑up preparations) or HS 3305 (preparations for skin cleansing). Buyers in the European Union, Canada and the Middle East frequently import such items, requiring compliance with the EU Cosmetics Regulation (Regulation (EC) No 1223/2009) and the Canadian Cosmetic Ingredient Hotlist. Common certifications requested by importers include ISO 22716 (GMP for cosmetics), FDA registration for over‑the‑counter topical products, and a Certificate of Origin to qualify for preferential tariffs under NAFTA/USMCA. Packaging for these products typically involves PET or HDPE bottles for gels, aluminum‑laminated tubes for deodorant sticks, and shrink‑wrapped jars for lotions, all of which are sized to fit standard 20‑ft or 40‑ft containers. Logistics for small‑volume cosmetics often use air freight for rapid delivery or sea freight in bulk cartons, with Incoterms such as FOB US port or CIF destination commonly applied.

Exporters from the United States must also provide a Material Safety Data Sheet (SDS) and a product specification sheet for each item, especially when the product contains active ingredients or preservatives. Importing countries may request a third‑party laboratory test report confirming limits for heavy metals (e.g., lead <10 ppm) and microbiological criteria (e.g., total viable count <100 CFU/g).

Sourcing from National Material Supply Co., LLC - Buyer Guidance

Buyers sourcing from National Material Supply Co., LLC should request a current SDS, a detailed specification sheet, and, where applicable, a Certificate of Analysis confirming pH, viscosity and preservative efficacy. For the skin gel and shave gel, an independent stability test covering at least three temperature cycles (4 °C, 25 °C, 40 °C) is standard practice to verify product integrity during transport. The aluminum‑free deodorant stick should be accompanied by a fragrance‑free declaration and a microbial limit test report, while the nail hardener requires a hardness rating and a polymer content analysis. Verification of ISO 22716 compliance or any FDA OTC monograph listing strengthens confidence in manufacturing practices. Buyers should also confirm packaging dimensions, net weight and container material to calculate freight costs accurately before placing an order.

Typical minimum order quantities for the listed items range from 500 units for the 8 oz gel to 2,000 units for the 16 oz Air Shave gel, with lead times of 15‑30 days after receipt of a purchase order and approved samples.

What product formats does National Material Supply Co., LLC offer for its skin‑care line?

The supplier lists an 8 oz Tend Skin gel in a PET bottle and a 16 oz Air Shave gel in a squeeze tube, both sized for retail distribution.

Are the deodorant sticks fragrance‑free and aluminum‑free?

Yes, the catalogue specifies an "Aluminum" & fragrance‑free deodorant stick, which typically uses alternative antiperspirant actives such as magnesium hydroxide.

What documentation should a buyer request for the nail hardener?

Buyers should ask for a Certificate of Analysis showing polymer concentration, a hardness rating (Shore D 55‑65) and a microbial limit test report.

Which HS codes are normally applied to these cosmetics products?

U.S. exporters generally classify skin gels, deodorant sticks and body lotions under HS 3304, while nail care preparations fall under HS 3305.

What certifications are commonly required for importing these items?

Importers often require ISO 22716 GMP certification, FDA registration for topical OTC products, and a Certificate of Origin for tariff purposes.

What are typical packaging and shipping methods for the listed products?

Products are packed in individual retail containers placed in corrugated cartons; shipments are usually sent in 20‑ft or 40‑ft containers using FOB US port or CIF destination terms.

What sample and testing procedures are advisable before a full order?

Request a physical sample for pH, viscosity and fragrance testing, and obtain a third‑party stability report covering at least three temperature cycles.

What are the usual minimum order quantities and lead times?

MOQ ranges from 500 units for the 8 oz gel to 2,000 units for the 16 oz gel, with lead times of 15‑30 days after order confirmation and sample approval.