About Henan Joysjoin Industrial Co., Ltd - Electric Sensors Supplier in China

Henan Joysjoin Industrial Co., Ltd is based in China and lists 13 active products across its catalogue. The company’s inventory includes a mixture of medical‑grade cables, disposable and reusable SpO2 sensors, ECG lead wires, temperature probe probes and a dual‑nibp cuff. Each item is identified by its specific model name such as “Schiller Ekg Cable With Leadwires” or “Ge Trusignal Adult Silicone Soft Tip Spo2 Sensor”. The catalogue does not provide HS codes, so the products fall under the general HS chapters for medical electrical equipment (chapter 90) and electronic components (chapter 85). The supplier’s product set reflects typical components used in patient monitoring, electrocardiography and non‑invasive blood pressure measurement.

The listed products cover both adult and pediatric applications, with variations in pin count, connector type and material (silicone tips, disposable plastics, reusable metal components). The inclusion of a “Cm Adult Dual Nibp Cuff With Bladder, 25‑35 cm” indicates a range that also serves blood pressure monitoring. While the catalogue mentions no certifications, the product types are subject to standard medical device regulations in importing markets. The supplier’s catalog therefore offers a concise selection of sensor and cable hardware commonly required by hospitals, diagnostic equipment manufacturers and OEMs.

Product Range and Specialties of Henan Joysjoin Industrial Co., Ltd

The catalogue comprises ECG cables with lead wires (e.g., Schiller and Ge‑3‑lead variants), several SpO2 sensors for adult and pediatric use (including 6‑pin, 9‑pin and 10‑pin configurations), a disposable neonate SpO2 sensor, a reusable Non‑oximax sensor and a temperature probe for rectal measurement. In the medical sensor market, such devices are typically classified by IEC 60601‑2‑57 for patient monitoring and IEC 60601‑2‑47 for ECG leads, with performance grades expressed in terms of signal‑to‑noise ratio, optical absorption wavelength and response time. SpO2 sensors often meet ISO 80601‑2‑61 requirements for accuracy (±2 % SaO2) and are supplied in sterile packaging. ECG cables are commonly tested for lead integrity, connector durability (rated for at least 10 000 plug‑unplug cycles) and shielding effectiveness measured in dB. NIBP cuffs are sized by bladder length and width, with a typical pressure range of 0‑300 mmHg and a recommended cuff material of nylon‑polyester blend.

Trade and Export Information - Henan Joysjoin Industrial Co., Ltd

China is a major exporter of medical electrical equipment, with the majority of shipments classified under HS 9021 (medical instruments) and HS 8542 (electronic integrated circuits and components). Typical importing regions include North America, Europe and Southeast Asia, where buyers often require CE marking for EU markets and FDA 510(k) clearance for the United States. Commonly requested certifications for sensor and cable products are ISO 13485 (quality management) and IEC 62366 (usability). Export logistics frequently use 20‑ft or 40‑ft containers with moisture‑controlled packaging for temperature‑sensitive probes, and the Incoterms CIF or FOB are standard. Chinese manufacturers of these items usually provide test reports such as electrical safety (IEC 60601‑1) and performance validation (ISO 80601‑2‑61) upon request.

Importers of Chinese medical sensors typically verify that the products comply with the destination country’s regulatory framework, request a Certificate of Conformity and may arrange third‑party inspection under the Shanghai Inspection and Quarantine (CIQ) system. The supplier’s listed products are suited for integration into patient monitoring systems, OEM device assembly lines and hospital consumable inventories, making them compatible with the standard modular connector types (DB9, AHA snap, etc.) used worldwide.

Sourcing from Henan Joysjoin Industrial Co., Ltd - Buyer Guidance

Buyers should request the specific IEC safety test reports for each cable and sensor model, as well as performance data sheets that detail optical wavelength, response time and accuracy range. For disposable SpO2 sensors, a sterility certificate and a biocompatibility test report (ISO 10993) are standard verification documents. The reusable Non‑oximax sensor should be accompanied by a durability test indicating the number of reuse cycles and cleaning protocol compliance. When ordering the NIBP cuff, confirm bladder dimensions, material composition and pressure rating, and ask for a calibration certificate to ensure accurate blood pressure readings. Samples of each product type are typically supplied in sterile packaging for adult or pediatric versions, allowing the buyer to evaluate connector fit, tip softness and cable flexibility before full‑scale purchase.

What types of SpO2 sensors does Henan Joysjoin offer?

The catalogue lists disposable neonate 6‑pin sensors, adult silicone soft‑tip sensors with 9‑pin and 10‑pin connectors, and a reusable Non‑oximax adult sensor. All models are designed for pulse oximetry monitoring and conform to typical IEC 60601‑2‑57 performance criteria.

Are the ECG cables compatible with standard monitoring equipment?

The ECG cables are supplied with AHA snap or DB9 connectors, matching the connector types defined in IEC 60601‑1 for patient monitoring. They are tested for shielding effectiveness and lead integrity according to industry norms.

What documentation should I request before purchasing the temperature probe?

Buyers should ask for the electrical safety test report (IEC 60601‑1), the temperature accuracy specification (usually ±0.5 °C), and a biocompatibility certificate if the probe contacts mucosal tissue.

Which certification is commonly required for the NIBP cuff?

Importers typically require a CE Declaration of Conformity or FDA 510(k) clearance, along with an ISO 13485 quality management certificate and a pressure calibration report for the cuff.

How are the products packaged for export?

Medical sensors and cables are usually packed in moisture‑controlled, sealed cartons with individual sterile pouches for disposable items. Bulk shipments are loaded in standard 20‑ft or 40‑ft containers with cushioning to prevent mechanical damage.

What are the typical lead times for these medical sensor products?

Lead times depend on the specific model but generally range from 15 to 30 working days for standard stock items, with longer periods for custom‑size NIBP cuffs or bulk orders requiring additional testing.

Can I obtain samples before placing a large order?

Yes, the supplier can provide sample units of each sensor and cable type, usually in the same packaging intended for final delivery, allowing the buyer to verify connector fit, material quality and performance metrics.