About Star Auto Solutions - Machined Components Supplier in India

Star Auto Solutions is based in India and currently lists five distinct product types in its catalogue. The supplier’s portfolio includes machined components, various spring products, rubber moulded items, automotive rubber moulded parts, and die‑casting components. Each entry is presented under the broader categories of Machined Components, Springs, Rubber Items, and Automobile Rubber Parts as defined in the supplied data. The catalogue does not provide HS codes, so classification must be inferred from standard tariff headings for similar goods. The supplier is classified as an imported tier with a harbor trust tier.

The machined parts are supplied as custom‑fabricated metal pieces suitable for assembly lines, while the spring range covers compression and tension designs typically fabricated from carbon steel or stainless steel. Rubber moulded parts are described generically, encompassing items produced from standard rubber compounds used in industrial applications. Automotive rubber moulded parts indicate components intended for vehicle interiors or under‑body systems, often requiring compliance with automotive durability standards. Die‑casting parts are listed without material detail but generally refer to zinc or aluminium alloy castings used in precision fittings. Buyers can therefore expect a product mix that spans both metal and elastomeric components for automotive and general manufacturing use.

Product Range and Specialties of Star Auto Solutions

Star Auto Solutions lists five product types: machined parts, springs, rubber moulded parts, automotive rubber moulded parts, and die‑casting parts. In the machined components segment, industry practice typically involves materials such as carbon steel, alloy steel, aluminium or brass, with tolerances ranging from ±0.1 mm for precision parts to ±0.5 mm for general applications. Surface finishes often adhere to Ra 0.8 µm or better, and heat‑treated grades like 42CrMo4 are common for high‑stress components.

Spring products are generally produced from spring‑grade steel (e.g., ASTM A228) or stainless steel (ASTM A313) and are specified by coil diameter, wire diameter, free length and load capacity, with hardness values around 45‑55 HRC. Rubber moulded items usually employ natural rubber (NR), styrene‑butadiene rubber (SBR) or EPDM, measured in Shore A hardness from 30 to 80 depending on application. Die‑casting parts are commonly made from zinc‑aluminium alloys (Zn‑Al 3) or aluminium‑silicon alloys, with typical casting tolerances of ±0.2 mm and surface roughness Ra 1.6 µm. These specifications align with standard HS chapters 84 (machinery parts), 73 (iron/steel articles), 40 (rubber products) and 76 (base metals) that classify similar goods.

Trade and Export Information - Star Auto Solutions

India is a major exporter of machined metal components, springs and rubber automotive parts, with primary destinations in the United States, European Union, Middle East and Southeast Asia. Export shipments of machined parts are usually classified under HS 8462 (machinery parts) or HS 7326 (iron or steel articles), springs under HS 7318, rubber products under HS 4016, and die‑casting parts under HS 7615. Buyers typically require compliance with ISO 9001 quality management and, for automotive applications, IATF 16949 or ISO/TS 16949 certifications, as well as material test certificates and CE marking where applicable.

Standard export logistics from Indian manufacturers involve FOB loading at major ports such as Nhava Sheva (Mumbai) or Chennai, with containerized shipments in 20‑ft or 40‑ft units. Packaging commonly includes wooden pallets with shrink‑wrap, and moisture‑resistant bulk bags for rubber components. Importers often request pre‑shipment inspection reports from agencies like SGS or Bureau Veritas, and may stipulate Incoterms CIF or DAP depending on the destination market. These trade practices are typical for the categories listed by Star Auto Solutions.

Sourcing from Star Auto Solutions - Buyer Guidance

When sourcing machined components from Star Auto Solutions, buyers should request a detailed drawing review, material certification (e.g., mill test report) and a first‑article inspection report that confirms dimensional tolerance and surface finish. For springs, a specification sheet should include wire diameter, coil count, load rating and hardness, accompanied by a tensile test report and compliance with ASTM standards.

Rubber moulded and automotive rubber parts should be supplied with a compound data sheet indicating the rubber type, Shore A hardness, tensile strength and ageing test results. Die‑casting parts require a material composition certificate and a dimensional inspection report, often verified against ISO 2768 tolerances. In all cases, buyers are advised to obtain ISO 9001 or relevant automotive quality system certificates, request sample pieces before full production, and verify that packaging meets ISO 12647 for moisture protection. Typical minimum order quantities range from 500 kg for bulk metal parts to 1 000 units for small rubber components, with lead times of 4‑8 weeks depending on complexity.

What types of machined components does Star Auto Solutions offer?

The catalogue lists generic machined parts that can be fabricated from steel, aluminium or brass according to buyer specifications. Typical industry offerings include precision brackets, shafts and custom‑shaped components with tolerances of ±0.1 mm to ±0.5 mm.

Which materials are used for the springs listed by Star Auto Solutions?

Spring products are usually produced from carbon steel or stainless steel grades that meet ASTM A228 or ASTM A313 specifications. Buyers should verify the steel grade and hardness (approximately 45‑55 HRC) before ordering.

How can I obtain a sample of the rubber moulded parts?

Request a sample by providing the desired rubber compound, dimensions and Shore A hardness. The supplier can ship a pilot batch in a sealed box, typically within two weeks of sample approval.

What certifications should I request from Star Auto Solutions for automotive rubber parts?

For automotive rubber components, ask for material safety data sheets, a rubber compound certification (e.g., ISO 1629), and any applicable ISO 9001 or IATF 16949 quality system certificates. CE marking documentation may also be required for EU markets.

What are the typical HS codes for the products offered by Star Auto Solutions?

Machined metal parts are commonly classified under HS 8462, springs under HS 7318, rubber moulded items under HS 4016, and die‑casting components under HS 7615. These codes are used by customs for tariff and inspection purposes.

What are the standard packaging and shipping methods for die‑casting parts from this supplier?

Die‑casting parts are usually packed in wooden crates with internal bracing, placed on pallets and shrink‑wrapped. Shipments are sent in 20‑ft or 40‑ft containers from Indian ports on FOB or CIF terms.

What is the usual lead time and minimum order quantity for the listed products?

Lead times vary from four to eight weeks depending on part complexity and material availability. Minimum order quantities are typically 500 kg for bulk metal items, 1 000 units for small rubber components, and 200 kg for die‑casting parts.