About Shanghai Electric Heavy Machinery Co., Ltd. - Industrial Motors and Metalworking Machinery Supplier in China

Shanghai Electric Heavy Machinery Co., Ltd. is a China-based industrial supplier operating from Shanghai with an active catalogue of 22 products spanning electric motors, induction melting furnaces, metal rolling and continuous casting equipment, bearings, and measurement instruments. The catalogue is concentrated in three HS code families: 8501.51 covering single-phase AC motors (used for the listed Vertical Hollow Shaft / VHS motors), 8455.21 covering rolling mills, and 8454.30 covering casting machinery. The motor line dominates the listing, with at least 14 of the 22 entries covering AC induction, DC, flameproof, explosion-proof, and vertical hollow shaft configurations, alongside two anemometer models under the scientific instruments category. The metalworking machinery segment of the catalogue covers the upstream and downstream processes used in non-ferrous and ferrous primary metal production: a 5-ton medium frequency induction melting furnace and a general induction melting furnace for melt preparation, a vertical billets casting machine and an R9m 6-strand continuous casting machine for billet forming, and an aluminium sheet rolling mill for downstream flat product output. The remaining entries cover bearings (NSK-bearing VHS motors), light and medium machinery, and industrial heating equipment, giving the supplier a cross-category industrial equipment profile rather than a single-niche focus. No company founding year, employee count, factory size, revenue figure, or client list is stated in the available facts, so none is asserted here.

Product Range and Specialties of Shanghai Electric Heavy Machinery Co., Ltd.

The motor catalogue covers the principal industrial AC and DC configurations in current use: three-phase asynchronous induction motors in standard and variable-frequency (YVFZ) variants, large Z DC motors, vertical hollow shaft (VHS) and TEFC VHS motors in ratings up to 500 HP, flameproof and explosion-proof motors for hazardous areas, and units supplied with NSK bearings under NEMA mounting conventions. Buyers sourcing from this category typically expect IEC 60034 or NEMA MG-1 frame compliance, IP54 or IP55 enclosure protection for TEFC designs, IE2/IE3 efficiency classes under IEC 60034-30-1, and Ex d IIB or Ex d IIC certification for the flameproof and explosion-proof lines. The cast iron frame, copper winding, and steel housing construction noted on the VHS TEFC NEMA NSK Bearing entry is the standard build for industrial VHS motors used in deep well pumps and large cooling tower fans. The metalworking machinery line covers the standard process chain for aluminium and steel billet production. Induction melting furnaces in this category are typically medium-frequency (150 Hz to 10 kHz) coreless crucible designs rated from 0.5 t to 10 t, with 5-ton being a common mid-capacity size; continuous casting machines are rated by strand count (the listed 6-strand unit with 9 m radius is a curved-mould bow-type caster typical for billet sections of 100 mm to 200 mm); and aluminium sheet rolling mills under HS 8455.21 are typically 4-high or 6-high cold rolling configurations handling 1050, 3003, 5052 and 6061 series alloys produced from recycled scrap. The two anemometer entries (YF6-4 and a generic anemometer) fall under meteorological and HVAC measurement instruments, typically cup or ultrasonic types with 0 to 30 m/s or 0 to 60 m/s ranges.

Trade and Export Information - Shanghai Electric Heavy Machinery Co., Ltd.

China is the world's largest exporter of electric motors and a leading exporter of metalworking machinery, with Shanghai and the broader Yangtze River Delta hosting the densest cluster of motor OEMs and metallurgical equipment builders. Industrial AC motors under HS 8501 and DC motors under HS 8501.31 are typically shipped to Southeast Asia, the Middle East, Africa, South America, and the CIS countries for use in water pumping, HVAC, mining, cement, and steel plant auxiliary drives. Metal rolling mills (HS 8455) and continuous casting machines (HS 8454) from China are commonly procured by steel and aluminium producers in India, Turkey, Iran, Vietnam, Indonesia, Egypt, and the Russian Federation, often as turnkey or semi-turnkey plant packages. The standard export packaging for these goods is seaworthy wooden crates or steel-framed cases with desiccant and vacuum foil for electrical windings, and 20 ft or 40 ft flat-rack containers for the casting and rolling equipment that exceeds standard container dimensions. For these product categories, buyers and end-users typically require ISO 9001 quality management certification on the manufacturer side, CE marking for goods entering the European Economic Area, ATEX certification for the flameproof and explosion-proof motors, and GOST or EAC certification for the Russian and CIS markets. Motors for the North American market generally need UL or CSA listing and NEMA Premium efficiency compliance. Pre-shipment inspection (commonly by SGS, BV, TUV, or Intertek) and a factory acceptance test (FAT) report are standard buyer requirements on capital equipment such as induction furnaces, casting machines, and rolling mills. Incoterms typically used in this segment are FOB Shanghai or Ningbo for motor shipments and CFR or CIF for metallurgical plant equipment, with payment by irrevocable L/C at sight or 30% T/T advance against the balance on B/L copy being the prevailing structure.

Sourcing from Shanghai Electric Heavy Machinery Co., Ltd. - Buyer Guidance

Before placing a trial order with a supplier in this category, a buyer should request the motor's nameplate data sheet, efficiency class certificate (test report per IEC 60034-2-1 or IEEE 112), and the dimensional drawing matched to IEC or NEMA frame standards. For flameproof and explosion-proof motors, the Ex certificate number, the notified body that issued it, and the specific gas group and temperature class must be confirmed in writing. On the metallurgical equipment side, the buyer should ask for the rated annual capacity in tons per year, the input stock specification (scrap grade, liquid metal temperature, billet section size), utility consumption per ton (kWh, water, gas), and a reference list of similar installations, ideally with contact details for end-user confirmation. A reasonable verification path is to start with a sample motor or a pilot furnace/casting machine order, request a third-party pre-shipment inspection, and require the supplier to provide an English-language operation and maintenance manual, a bill of materials with critical spare parts list, and a wiring diagram. Lead time for standard AC motors is typically 4 to 8 weeks for repeat builds and 10 to 16 weeks for engineered VHS or explosion-proof units; metallurgical plant equipment lead times run 6 to 12 months from order. Payment milestones tied to design approval, FAT, and shipment are standard for capital equipment. No claim is made here about this supplier's response time, inspection history, or quality performance, as those data points are not in the available facts.

What types of electric motors does Shanghai Electric Heavy Machinery Co., Ltd. list?

The catalogue covers three-phase AC induction motors (standard, variable-frequency YVFZ, and vertical hollow shaft VHS designs up to 500 HP), DC motors including large Z DC units, flameproof and explosion-proof motors, TEFC VHS motors with NSK bearings, and three-phase asynchronous induction motors. Frame sizes typically follow IEC 80 to 450 or NEMA 143 to 580 depending on the rating.

Which HS codes apply to the metalworking machinery in the catalogue?

The aluminium sheet rolling mill is listed under HS 8455.21 (rolling mills, cold), and the vertical billets casting machine is listed under HS 8454.30 (casting machines). The VHS TEFC NEMA NSK Bearing motor is listed under HS 8501.51 (AC motors, single-phase, output not exceeding 750 W and multi-phase units above 750 W fall under 8501.52). Buyers should confirm the exact subheading with the supplier based on the specific motor rating ordered.

What specifications should a buyer request when ordering an induction melting furnace?

Request the rated crucible capacity in tons (the listed 5-ton unit is a medium-frequency coreless type), the operating frequency in Hz, the melting rate in tons per hour, the specific power consumption in kWh per ton, the coil voltage, and the cooling water requirement in m³ per hour. A refractory lining specification and the type of scrap or ingot the furnace is designed for should also be confirmed in writing.

Which certifications should a buyer ask for on the explosion-proof and flameproof motors?

Ask for the ATEX Ex d certificate with the notified body number, the gas group (IIA, IIB, or IIC) and temperature class (T1 to T6), the IECEx certificate of conformity if the destination is outside the EU, and any GOST-R or EAC certification if the motors are destined for Russia or the Eurasian Economic Union. For North American sites, UL or CSA hazardous location listings should be requested.

What is the typical minimum order quantity and lead time for industrial motors from Chinese suppliers?

Standard catalogue AC motors are commonly sold from a single unit with lead times of 4 to 8 weeks for repeat specifications and 10 to 16 weeks for engineered or explosion-proof builds. Custom ratings, special voltages, or non-standard frames usually carry higher minimum order quantities and longer lead times, and this should be confirmed directly with the supplier at the quotation stage.

What documents should accompany a shipment of metal rolling or casting machinery?

Capital equipment shipments typically come with a commercial invoice, packing list, bill of lading, certificate of origin (China or any preferential origin the buyer qualifies for), insurance policy if sold CIF, the original FAT report, an English-language operation and maintenance manual, a bill of materials, a foundation drawing, and the electrical schematic. For CE-marked components, the EU Declaration of Conformity should also be included.

Which export packaging is standard for motors and metallurgical equipment shipped from Shanghai?

Motors are typically packed in seaworthy wooden crates with desiccant and a waterproof outer wrap, while large VHS motors and DC machines above frame 400 are usually crated in steel-framed wooden cases. Induction furnaces, casting machines, and rolling mills are almost always shipped as breakbulk or in flat-rack containers due to their dimensions, with the heavy bases and gearboxes bolted to timber skids and protected by heat-treated ISPM 15 stamped wood.

Which Incoterms are most commonly used for these products?

FOB Shanghai or FOB Ningbo is the most common basis for motor shipments where the buyer arranges ocean freight. For capital equipment such as induction furnaces, continuous casters, and rolling mills, CFR or CIF to the destination port is more typical, with the supplier arranging sea freight and marine insurance. The chosen Incoterm should be agreed in writing before order confirmation.