About Back Bone Impex - Tiles Supplier in India

India hosts Back Bone Impex, which currently lists seven active tile products in its catalogue. The supplier focuses on ceramic and porcelain tile formats, covering wall tiles, outdoor tiles, glazed vitrified (GVT) tiles and large slab formats, each defined by precise dimensions such as 300 × 600 mm, 200 × 600 mm, 500 × 500 mm, 600 × 1200 mm and 800 × 1600 mm. The product titles differentiate matte and glossy finishes for GVT tiles and specify outdoor suitability for the 500 × 500 mm size. All items fall under the broader tile category, which aligns with HS Chapter 69 for ceramic products. The catalogue does not provide HS‑code numbers for individual items, but the listed dimensions match standard industry sizing for both residential and commercial applications.

Product Range and Specialties of Back Bone Impex

The catalogue offers wall tiles in 300 × 600 mm and 200 × 600 mm formats, a 500 × 500 mm outdoor tile, two 600 × 1200 mm glazed vitrified tiles (matte and glossy), a 600 × 600 mm porcelain tile and an 800 × 1600 mm slab tile. In the tile industry, wall tiles are typically rated by PEI (Porcelain Enamel Institute) grades ranging from R9 for light residential use to R10‑R11 for heavy commercial traffic, while outdoor tiles often require water absorption below 0.5 % and frost resistance. Glazed vitrified tiles are commonly produced with a body density above 2.3 g/cm³ and a surface hardness measured by Mohs 6 - 7. Slab tiles of 800 × 1600 mm are frequently used for large‑area flooring and are supplied in thicknesses of 8‑12 mm, with a typical flexural strength of 30‑40 MPa.

Trade and Export Information - Back Bone Impex

India is a major exporter of ceramic and porcelain tiles, with key markets in the Middle East, Europe, North America and Africa. The HS‑code 6907 covers most of the products listed, and shipments are usually packed on Euro pallets within 20‑ or 40‑ft containers, each container holding 20‑25 m² of slab tiles or up to 100 m² of smaller wall tiles depending on packaging. Importers commonly request ISO 9001 quality‑management certification, CE conformity for EU markets, and compliance with ASTM C1026 for water absorption. Indian tile exporters also adhere to the Indian Standards (IS 15658) for vitrified tiles, which specify surface hardness, slip resistance (ASTM C1028) and frost durability.

Sourcing from Back Bone Impex - Buyer Guidance

Buyers should obtain a product data sheet that lists dimensions, thickness, PEI rating, water absorption, frost resistance and surface finish (matte or glossy). Request test reports for water absorption (≤0.5 %), flexural strength (≥30 MPa) and slip resistance (ASTM C1028 classification). Because the supplier does not list certifications, ask for copies of ISO 9001, CE‑Marking or any relevant Indian Standard certificates before confirming orders. Verify packaging details - pallets wrapped in stretch film, cartons sized to protect the tile surface, and moisture‑proof liners for outdoor tiles - to reduce breakage during transit.

What dimensions are available from Back Bone Impex?

The supplier lists tiles in seven sizes: 300 × 600 mm, 200 × 600 mm, 500 × 500 mm, 600 × 1200 mm (matte and glossy GVT), 600 × 600 mm porcelain, and 800 × 1600 mm slab.

Are the 600 × 1200 mm tiles glazed or unglazed?

Both matte and glossy finishes are offered as glazed vitrified tiles (GVT), which provide a dense, low‑porosity surface suitable for high‑traffic areas.

Which HS code applies to these tiles?

Ceramic and porcelain tiles of the listed sizes are generally classified under HS code 6907, the standard chapter for glazed and unglazed ceramic products.

What certifications should a buyer request?

Buyers typically request ISO 9001 for quality management, CE‑Marking for EU compliance, and any relevant Indian Standard certificates such as IS 15658 for vitrified tiles.

What is the typical minimum order quantity?

For tile shipments, minimum orders are often calculated by container capacity - roughly one 20‑ft container (≈20 m² of slab tiles) or a 40‑ft container (≈40‑50 m² of smaller wall tiles), depending on packaging.

What lead time is common for Indian tile exporters?

Lead times generally range from 30 to 45 days after order confirmation, allowing for production, quality inspection and container loading.

How are the tiles packaged for export?

Tiles are usually packed on Euro pallets, wrapped in stretch film, and placed in cardboard cartons sized to the tile dimensions; slab tiles may receive additional edge protection and moisture‑proof liners.